AudioCodes Mediant 2000 User Manual

1 MMiiccrroossoofftt EExxcchhaannggee SSeerrvveerr 22000077 UUnniiffiieedd MMeessssaaggiinngg PPBBXX CCoonnffiigguurraattiioonn NNoott

10 Step 6: Trunk Group Setup

11 Step 7: TDM BUS Setting

12 Step 8: CAS Table Download Note: The CAS file must be downloaded to the Mediant 2000. A suitable CAS file is attached to this document (refer to

13 Step 9: Trunk Setting Setup

14 Step 10: Voicemail In-Band DTMF Setup

15 Step 11: FAX Setup

16 Step 12: General Setup

17 Step 13 : General Setup (Cont.) • EnableMWI = 1 • SubscriptionMode = 1 • LineTransferMode = 1 • IsSpecialDigits = 1 • EnableDetectRemoteMACC

18 Step 14: Reset Mediant 2000 Click Reset to reset the gateway.

19 4.1. Configuration Files The ZIP file includes the following files: • Audiocodes configuration ini file (.ini file extension). • Audiocodes T1

2 Content This document describes the configuration required to setup Avaya S8300 and AudioCodes Mediant 2000 using T1 CAS In-band DTMF Tones as the

20 4.2. TLS Setup The specific gateway software version used in this PBX Configuration Guide was not tested for TLS. However, TLS was tested success

21 Step 2: SIP Environment and Gateway Name Setup Note: Assign an FQDN name to the gateway (for example, gw1.m2k.audiocodes.com). Any gateway name t

22 Step 3: SIP Environment Setup (Cont.)

23 Step 4: DNS Servers Setup Note: Define the primary and secondary DNS servers' IP addresses so that they correspond to your network environme

24 Step 5: Internal DNS Setup Note: If no DNS server is available in the network, define the internal DNS table where the domain name is the FQDN o

25 Step 6: NTP Server Setup Note: Define the NTP server’s IP address so that it corresponds to your network environment (for example, 10.15.3.50).

26 Step 7: Generate Certificate Setup Use the screen below to generate CSR. Copy the certificate signing request and send it to your Certification Au

27 Step 8: Uploading Certificates Setup The screen below is used to upload the sign certificates. In the “Server Certificate” area, upload the gatew

28 5. PBX Setup Notes Information used for this test case: • Digital VoiceMail ports: ext. 5061 – 5084 ,24 T1 Channel • VoiceMail Hunt Group Pilot

29 Step 1: Add Station with Coverage Path Add a station using the Add Station command, and then configure the station using the below settings (in th

3 1. Components Information 1.1. PBX or IP-PBX PBX Vendor Avaya Model S8300 Software Version R013x.01.2.632.1 Telephony Signaling T1 CAS In-ban

30 Step 2: Define the Coverage Path Properties Add a coverage path using the Add Coverage Path command. Configure the coverage path properties using

31 Step 3: T1 Setting using E1/T1 Card Define T1 using the E1/T1 card that is connected to the Mediant 2000, using the Add DS1 command.

32 Step 4: Configuring T1 Ports Configure the ports on the T1 circuit. Note that the parameter ‘Type’ must be set to VMIFD to enable DTMFs. For T1 de

33 Step 5: Add a Hunt Group Add a hunt group using the Add Hunt Group command. Define the hunt group number (for example, 3) and properties using the

34 Step 6: Assign T1 Ports to Hunt Group Assign the T1 ports that you defined in Step 4 to the hunt group.

35 Step 7: Viewing Mode-code Related System Parameters and Feature Access Codes The DTMF signals sent from the PBX to the voice mail system providing

36 Feature Access Code: Below is the feature access code that defines the code sent from the gateway to the PBX for activating / deactivating Message

37 5.1. TLS Setup • N/A. 5.2. Fail-Over Configuration • N/A. 5.3. Tested Phones Avaya 2420 Model Telephone. 5.4. Other Comments None.

38 6. Exchange 2007 UM Validation Test Matrix The following table contains a set of tests for assessing the functionality of the UM core feature set

39 Dial the extension for the AA and confirm the AA answers the call. 6 Call Transfer by Directory Search. 6a Call Transfer by Directory Searc

4 2. Prerequisites 2.1. Gateway Prerequisites The gateway also supports TLS (in addition to TCP). This provides security by enabling the encryption

40 Confirm the FAX is received in the user’s inbox. 10 Setup TLS between gateway/IP-PBX and Exchange UM. Replace this italicized text with your TL

41 6.1. Detailed Description of Limitations Failure Point None Phone type (if phone-specific) Call scenarios(s) associated with failure point L

42 7. Troubleshooting The tools used for debugging include network sniffer applications (such as Ethereal) and AudioCodes' Syslog protocol. The

43 3. To determine the Syslog logging level, use the parameter Debug Level and set this parameter to '5'. 4. Change the CDR Report Level

44 Appendix 1. Dial Pilot Number and Mailbox Login • Dial the pilot number of the UM server from an extension that is NOT enabled for UM. • Confir

45 b. From an External Phone a. From an external phone, dial the extension for a UM-enabled user and leave a voicemail message. b. Confirm the voi

46 • Note: Even though some keys are associated with three or four numbers, for each letter, each key only needs to be pressed once regardless of th

47 • Once it is received in the user’s inbox, use OWA’s Play-On-Phone to dial an internal extension. • Confirm the voicemail is delivered to the co

48 9. FAX • Use the Management Console or the Management Shell to FAX-enable a user. • Management Console: a. Double click on a user’s mailbox an

49 12. Message Waiting Indicator (MWI) • Although Exchange 2007 UM does not natively support MWI, Geomant has created a 3rd party solution - MWI2007

5 4. Gateway Setup Notes Step 1: SIP Environment Setup

6 Step 2: Routing Setup Note: The Proxy IP Address must be one that corresponds to the network environment in which the Microsoft Unified Messaging

7 Step 3: Coder Setup

8 Step 4: Digit Collection Setup

9 Step 5: Manipulation Routing Setup